Full central heating systems, power flushes, radiator upgrades, pipework, zoning and controls across Greater Manchester. Warm, quiet, evenly heated homes — no cold spots, no banging, no wasted gas.
Gas Safe Reg. 636807 · WaterSafe · APHC member · 12-month workmanship guarantee
Full central heating work — new systems, extensions, rebuilds, power flushes, radiator and pipework upgrades, zoning and controls. Whether you're moving from an old gravity-fed system to a modern sealed system, adding radiators for an extension, or fixing an unbalanced house, we design the system to the property, not the other way round.
Homeowners planning an extension or renovation; anyone with cold radiators, noisy pipes, or a house that never heats evenly; landlords upgrading tired systems between tenancies; and buyers of older homes needing the heating brought properly up to date.
If radiators are cold at the top, noisy, or slow to warm — the system needs balancing or flushing. If the boiler is being replaced, upgrading the system at the same time typically pays back within a couple of heating seasons. If you're adding rooms, the heating needs redesigning, not just extending.
Central heating is a system, not a collection of parts. Skip the heat-loss calculation, the balance or the flush and even a premium boiler will short-cycle, waste gas and fail early. Get the system right and your boiler lasts longer, your bills drop and every room heats evenly.
Most 'boiler problems' are actually system problems. A modern condensing boiler dropped onto an old, sludged, unbalanced system won't last — and won't save the gas you were promised. Fix the system, fix the boiler.
An unbalanced system heats some rooms and starves others. The boiler runs longer to compensate, so gas bills stay high while comfort stays low.
Untreated systems build up magnetite sludge that erodes pumps, blocks radiators and destroys heat exchangers — the single biggest cause of premature boiler failure.
Poor pipework, no air separators, no balancing and no chemical dose leads to noise, cold spots and repeated pressure loss.
Adding radiators to under-sized flow-and-return pipework starves the far end of the house. It usually shows up the first cold snap after the work's done.
Every job follows the same disciplined sequence, so you always know where we are and what's next.
Room-by-room heat-loss calculation, existing pipework and radiator survey, controls audit and mains pressure test — before we quote anything.
We size radiators to each room, design pipework to actual flow rates, choose the right zoning and controls, and specify filtration and chemical dose.
You get a written, itemised fixed price covering boiler, cylinder, radiators, pipework, controls and any building work. No vague ranges.
New pipework, radiators and controls fitted, full power flush and chemical dose, magnetic filter and air separator added, system balanced.
We walk you through the controls, hand over the benchmark logbook and set up annual service reminders — so the whole system stays healthy.
Correctly sized radiators, balanced flows and proper controls mean every room hits temperature — no cold spots, no banging, no lukewarm rads.
A well-designed, well-controlled system typically cuts gas use significantly versus an old un-balanced one — often more than switching the boiler alone.
Filtration, chemical dose and proper commissioning protect the heat exchanger and dramatically extend boiler life.
Multi-zone controls with TRVs, weather compensation and smart thermostats — heat only the rooms you're using, when you're using them.
Systems designed so radiators can be added later without starving the rest of the house.
Boiler, cylinder, pipework, radiators, controls and underfloor — one Gas Safe team responsible end-to-end.
For new builds, full renovations and system rebuilds we design the whole thing from scratch — heat-loss calculations, radiator sizing, pipework routing, zoning strategy, controls specification and cylinder choice.
For sludged, noisy or under-performing systems we carry out full power flushes with the right chemical dose, then fit magnetic filters and air separators to keep the system clean. Power flushing is often the difference between a boiler that lasts 6 years and one that lasts 15.
Old, under-sized or badly-placed radiators are a common cause of cold spots. We resize using proper heat-loss figures, refit with TRVs, and rebalance the whole system — usually a same-day job with a noticeable difference before the engineer leaves.
Modern zoning — with TRVs on every radiator, weather compensation and a smart thermostat — heats only what you're using, when you're using it. See our smart heating controls page for detail; on new systems we specify controls as part of the design.
Wet underfloor heating integrates with the same boiler and cylinder as radiators, either as the whole system or a hybrid (e.g. UFH downstairs, radiators upstairs). We design manifolds, zoning and controls together — see the underfloor heating page for detail.
Every image below is from a real Eco Plumbing & Heating Solutions job across Greater Manchester. No stock photography.
It depends on property size, radiator count, pipework routing, cylinder choice, controls and zoning. We give a written itemised price after a survey rather than a range on the phone.
A typical whole-house new system is one to two weeks depending on property size and access. Boiler-only swaps with a system flush are usually one to two days.
If your radiators have cold spots, the system is noisy, or you're fitting a new boiler onto an older system — usually yes. We survey first and only recommend it where it'll genuinely help.
Yes — but properly. Adding radiators to under-sized pipework starves the rest of the house. We recalculate heat loss and check flow rates before quoting.
Yes. We fit and service mains-pressure unvented cylinders (G3 qualified) as part of full central heating installs or as standalone hot-water upgrades.
Yes — we specify smart thermostats and multi-zone controls as part of the system design. See our smart heating controls page for detail.
We handle the plumbing, gas, pipework and controls end-to-end. For plastering, tiling and joinery we bring in trusted trades we've worked with for years, coordinated by us.
Yes. Every job carries a 12-month workmanship guarantee, on top of any manufacturer warranty on parts we fit.
Rochdale, Oldham, Manchester, Salford, Bury, Ashton-under-Lyne, Heywood, Middleton, Shaw and surrounding Greater Manchester areas.
Book a free central heating survey and get a written, itemised quote — with radiator schedule, control options and no obligation to go ahead.
One team, one standard — across every plumbing and heating job in Greater Manchester.
